ملخصات الابحاث

المجالات البحثية

الابحاث العلمية

1 - Modeling electrospun PLGA nanofibers’ diameter using response surface methodology and artificial neural networks (2022).

2 - Study of bearing strength for injection molded GFRPP composites under dry and wet conditions (2022).

3 - Comparison between bearing strengths of molded‑in and machined holes of GFR/PP composites. (2022).

4 - Effect of ultrasonic parameters on the mechanical properties of glass fiber reinforced polyester filled with nano-clay (2022).

5 - Can ultrasonic parameters affect the impact and water barrier properties of nano-clay filled glass fiber/polyester composites? (2022).

6 - Effect of through-the-thickness position of aluminum wire mesh on the mechanical properties of GFRP/Al hybrid composites (2021).

7 - INVESTIGATION AND PREDICTION OF ABRASIVE WEAR RATE OF HEAT-TREATED HCCIS WITH DIFFERENT CR/C RATIOS USING ARTIFICIAL NEURAL NETWORKS (2021).

8 - Effect of incorporating aluminum wire mesh on the notched and un-notched strengths of glass fiber/epoxy composites (2021).

9 - The influence of incorporation of silica and carbon nanoparticles on the mechanical properties of hybrid glass fiber reinforced epoxy (2019).

10 - New nonlinear regression modeling and multi-objective optimization of cutting parameters in drilling of GFRE composites to minimize delamination (2019).

11 - Improvement of Hardness and Wear Resistance of Glass Fiber Reinforced Epoxy Composites by the Incorporation of Silica/Carbon Hybrid Nanofillers (2018).

12 - A novel polystyrene/epoxy ultra‐fine hybrid fabric by electrospinning (2018).

13 - Fabrication and characterization of functionally graded nanoclay/ glass fber/epoxy hybrid nanocomposite laminates (2017).

14 - The effects of nano-silica/nano-alumina on fatigue behavior of glass fiber-reinforced epoxy composites (2017).

15 - Enhancement of water barrier properties and tribological performance of hybrid glass fiber/epoxy composites with inclusions of carbon and silica nanoparticles (2017).

16 - Effect of TiO2 nano particles content on tensile and wear properties of GFRE composites (2015).

17 - Drilling Analysis of Woven GFR/Epoxy Composites (2013).

18 - Prediction of Abrasive Wear Rate of in Situ Cu–Al2O3 Nanocomposite using Artificial Neural Networks (2012).

19 - Nano-Reinforcement Effects on Tensile Properties of Polymeric Composite Materials (2011).

20 - Prediction of Sliding Wear Rate of Extruded Al–SiC Composite using Artificial Neural Networks (2011).

21 - Machinability Analysis in Drilling Woven GFR/Epoxy Composites: Part II- Effect of Drill Wear (2010).

22 - Machinability Analysis in Drilling Woven GFR/Epoxy Composites: Part I- Effect of Machining Parameters (2010).

23 - Ultrasonic Mixing of Nanoparticles in Epoxy Resin (2010).

24 - Experimental Evaluation of Delamination in Drilling of Fiber Reinforced Polymeric Composite Materials (2009).

25 - Prediction of Delamination Size in Drilling FRP Composite Materials using Artificial Neural Networks (2009).

26 - On the Prediction of Surface Roughness in Turning Operation using Artificial Neural Networks (2000).

تسجيل الدخول

دخول

صفحاتنا
الدعم الفنى
لتعديل بيانات أعضاء هيئة التدريس أرجو مراسلة مركز تكنولوجيا معلومات الجامعة قسم MIS
لإستكمال بيانات أعضاء هيئة التدريس
أو الإتصال ب : 25162
إتصل بنا

2014 all rights reserved. Zagazig University